Equipment in high demand
DL-CR50013
  • Description
  • Package contents
  • Manual

DL-CR 50013. Universal adapter for CR truck injectors (Bosch , Denso, Delphi Smart)

Part 1

Part 2

Universal adapter for CR truck injectors (Bosch , Denso, Delphi Smart) for supply and backflow lines at angles of 0⁰, 4⁰ and 13⁰.

Применяется как для испытаний форсунок на стендах, так и при проверке распылительной части форсунок на ручном прессе.

Technical data

Injector types Common Rail
Maximum diameter of injector 30 mm
O-ring for the backflow fitting connection vition
Dimentions 37 x 62 x 62 mm
Weight 1050 g
  • The scope of delivery :
  • DL-CR30219 Adapter body
  • DL-CR50035 Bracket with connecting piece and fitting for backflow connection
  • DL-CR30419 Adapter for backflow connection for Delphi Smart CR injector
  • DL-CR30238 Long fitting for supply line
  • DL-CR30225 Normal fitting for supply line
  • DL-CR30661 Adapter for backflow connection for Bosch CR injectors 0445120147, 0445120098
  • DL-CR30269 Fitting for backflow connection of Delphi Smart, Denso, Bosch injectors 0445120147, 0445120098.
  • D-27-200078 O-ring for backflow fitting (2pcs).
  • Allen key 3 mm.

Manual

Select from the set the items to be installed on the type of injector you are going to test.

Install the fitting (DL-CR 30238 or DL-CR 30225) to connect the supply to the clamping sleeve of the adapter body. If the injector has an angle of 13 degrees it is necessary to use an elongated fitting (DL-CR 30238) to connect the supply.

Install the adapter body (DL-CR 30219) onto injector. If the injector has an angled inlet, before installing the adapter body you need to fix the adapter strip at the required angle (“0”, “4” or “13” degrees).

Secure the fitting for supply line. To do this, direct the tip of the fitting for supply line to the place of fuel supply and tighten the clamping sleeve of the adapter body. Use 12 mm wrench, to hold the supply connection from turning and use a second 22 mm wrench to tighten the clamping sleeve of the adapter housing.

ATTENTION! The force applied when tightening the clamping sleeve must be 36-40 Nm

Install the bracket with a fitting for the backflow on the injector. The connection must be previously unscrewed, so that it does not interfere with the installation.

After tightening the connection, align its tip with the injector backflow. The fitting is screwed by hand.

ATTENTION! The force applied when the connection for backflow line is tightened should not be too large. It is necessary to check when tightening the seal of the rubber ring to the edges of the injector backflow opening.If the tightening torque is excessive, the rubber ring may twist and lose its tightness.

Features of mounting the adapter on some injectors BOSCH 0445120147, 0445120098

Before installing the adapter body, install the adapter for backflow connection (DL-CR 30419).

Install the adapter body (DL-CR 30219) on the injector.

Screw in the adapter rack fitting for backflow connection (DL-CR 30269) of the Delphi Smart, Denso, Bosch injectors.

ATTENTION! Before tightening combine the hole in the adapter with the tip of the fitting until the hole is completely aligned with the tip of the fitting. The force applied when the connection for backflow line is tightened should not be too large. It is necessary to check when tightening the seal of the rubber ring to the edges of the injector backflow opening.

Features of mounting the adapter on the DENSO injectors

Install the adapter case on the injector (DL-CR 30219).

Secure the fitting for supply line. To do this, direct the tip of the fitting for supply line to the place of fuel supply and tighten the clamping sleeve of the adapter body. Use 12 mm wrench, to hold the supply connection from turning and use a second 22 mm wrench to tighten the clamping sleeve of the adapter housing.

ATTENTION! The force applied when tightening the clamping sleeve must be 36-40 Nm

Screw in the adapter rack fitting for backflow connection (DL-CR 30269) of the Delphi Smart, Denso, Bosch injectors.
The fitting is screwed by hand.
ATTENTION!
The force applied when the connection for backflow line is tightened should not be too large. It is necessary to check when tightening the seal of the rubber ring to the edges of the injector backflow opening.

Features of adapters installation on injectors DELPHI Smart Injector

Install the adapter case on the injector (DL-CR 30219).
Secure the fitting for supply line. To do this, direct the tip of the fitting for supply line to the place of fuel supply and tighten the clamping sleeve of the adapter body. Use 12 mm wrench, to hold the supply connection from turning and use a second 22 mm wrench to tighten the clamping sleeve of the adapter housing.

ATTENTION! The force applied when tightening the clamping sleeve must be 36-40 Nm

Before installing the adapter body, install the adapter for backflow connection (DL-CR 30419)of CR Delphi Smart .

Screw in the adapter rack fitting for backflow connection (DL-CR 30269). Tighten by hand.

ATTENTION! Before tightening combine the hole in the adapter with the tip of the fitting until the hole is completely aligned with the tip of the fitting.
The force applied when the connection for backflow line is tightened should not be too large. It is necessary to check when tightening the seal of the rubber ring to the edges of the injector backflow opening.